全部

全部
产品管理
新闻资讯
介绍内容
企业网点
常见问题
企业视频
企业图册

Search

Product Introduction

As a designated manufacturer of rectifiers by the former Ministry of Machinery Industry, we specialize in the production of electrolytic and electrochemical rectifiers. We have numerous production achievements and rich manufacturing experience in the electrolytic copper industry.

Product Classification

KGLF11-450A/170V

Synchronous motor

The KGLF11 thyristor excitation device is suitable for constant excitation of synchronous motors starting under heavy or light loads, and is also applicable for excitation of small generators. This device has the following features:<br /> 1.The rotor circuit of the synchronous motor adopts a three-phase fully controlled rectifier bridge fixed excitation circuit, maintaining the inherent starting characteristics of the synchronous motor.<br /> 2. There is no direct electrical connection with the stator circuit of the synchronous motor. Therefore, the synchronous motor can be designed as high-voltage (3-6-10KV) or low-voltage (380V) according to the conditions of the power grid, and full-voltage starting or reduced-voltage starting is not restricted.<br /> 3.When starting a synchronous motor at full voltage, when its speed reaches sub-synchronous, excitation can be put into operation with a rotor slip of 5% to 4% in the forward polarity to drag the synchronous generator motor into synchronous mode. Alternatively, excitation operation can be delayed for a certain period of time after the motor is connected to the power grid.<br /> 4. For a synchronous motor starting with reduced voltage, when the rotor speed reaches about 90% of the synchronous speed, the reduced voltage starting reactance or resistance is automatically disconnected, and the full voltage is automatically engaged to accelerate the start-up of the synchronous motor to sub-synchronous speed. The excitation is carried out in a stepwise manner with a slip of 5% to 4%, thus pulling the synchronous motor into synchronous operation. <br />5. When the grid voltage fluctuates, it features negative voltage feedback and automatically maintains a basically constant excitation. When the grid voltage drops to a certain percentage, it suddenly intensifies the excitation, with a strong excitation time of 10 seconds or 40 seconds.

KGLF11-450A/170V

Three-phase thyristor trigger control board

It adopts a 32-bit industrial-grade high-performance microprocessor and is designed in accordance with highly digital safety standards. It supports both network remote control and on-site control methods, integrating three regulation modes: open-loop voltage regulation, closed-loop constant voltage regulation, and constant current regulation. It features fault alarm and is applicable in various different scenarios with stable performance. It integrates three regulation methods: open-loop voltage regulation, closed-loop constant voltage regulation and constant current regulation. It controls the thyristor to achieve constant voltage and current limiting or constant current and voltage limiting. The fault alarm and control board are equipped with functions such as phase loss protection, soft start upon power-on, soft shutdown, constant current output, constant voltage output, overvoltage protection, overcurrent protection, short circuit protection, and working status indication. It features triggering methods such as three-phase fully controlled bridge rectification, two-side star rectification circuits, and in-phase reverse parallel rectification circuits. It can trigger thyristors below 5000A and is suitable for various load types including resistive loads, inductive loads, capacitive loads, and the primary side of transformers for voltage and current regulation in all industrial fields.<br /> It is widely applied in equipment such as electrolysis, electroplating, battery charging and discharging, three-phase thyristor power supply electric heating temperature control, and arc discharge control

Three-phase thyristor trigger control board

Radiator

Power frequency high current test device

This equipment is a test power supply designed and produced in accordance with the requirements stipulated in Clause 7.8.2 of the power industry standard DL-1312-2013 "Technical Conditions for Copper Clad Steel for Grounding in Power Engineering". The load is the grounding electrode test sample. Connect the test subject to the test circuit, apply current to gradually increase the temperature of the test subject to 90% of the melting value, then stop the current increase and maintain this temperature for 3 to 10 seconds, and then stop applying current. When the test subject cools to a certain temperature below 100℃ (this temperature can be set), proceed to the next high-current test cycle. After a total of three high-current cycle experiments, the test was concluded.

Power frequency high current test device

IGBT

IGBT

IGBT

Transformer

Transformer

Transformer

Project Case

Project Case

< 1 2 3 4 >

Your Best Choice

Strong R&D Capability

Global Service Network

Customized Solutions

Expert Technical Team

Professional

Provide customers with professional services

Online Consultation

Learn
Support

CONTACT US

Address: C5-1-1, Huazhong International Industrial Park, Yangluo Port, Wuhan City

WhatsApp: +86 136017171890

E-MAIL: lzh@wrtpower.com

Copyright © 2025 Wuhan Rectifier Research Institute

Business licence

Powered by：CEglobal

中企跨境-全域组件 1.82 制作前进入CSS配置样式

导航下拉添加类名.active

在线客服添加返回顶部

右侧在线客服样式 1,2,3 1

图片alt标题设置： Wuhan Rectifier Power

表单验证提示文本： Content cannot be empty!

循环体没有内容时： Sorry,no matching items were found.

CSS / JS 文件放置地